==ФоРуМ==

[ Новые сообщения · Участники · Правила форума · Поиск · RSS ]

Страница 1 из 1 1
Модератор форума: droyd, pas_tol

==ФоРуМ== » TruTops » TruTops » Trumpf TLF750 Problem - need help!

Trumpf TLF750 Problem - need help!

caredas

Оффлайн

Понедельник, 23.09.2013, 11:53 | Сообщение # 1

Сообщений:

Награды:

Замечания:

Hi to all,

I have a problem with combined laser/punching machine Trumpf TC240L. The laser unit is: TLF 750.
The punching machine is OK, but on the laser control panel there are next error messages:

1. Machinendaten fehlerhaft
2. Gasdruckstrahlfalle zu niedrig S588
3. Fehler Leistungsziklen-Daten

I will attach photo of the display.

Can someone explain to me what these errors mean?

And the other thing... i need any documentation for the machine in English or Russian.

Thanks in advance!

And sorry for the English!

trumpf2030

Оффлайн

Понедельник, 23.09.2013, 21:50 | Сообщение # 2

Сообщений:

Награды:

Замечания:

Gasdruck Lasergas zu niedrig - laser gas pressure too low! Check laser gases inlet or setting amount of laser gases...

Gasdruck strahlfalle - check beam trap! But i don´t know how is beam trap controlled

Floyd

Оффлайн

Вторник, 24.09.2013, 10:50 | Сообщение # 3

Сообщений:

Награды:

Замечания:

Цитата (caredas)

1. Machinendaten fehlerhaft

- change two CR123A Lithum cell on the big green circuit board.

Цитата (caredas)

3. Fehler Leistungsziklen-Daten

- enter the data of 100 cycles (Leistungsziklen-Daten) from documentation through the TASK keyboard. Your laser "forgot"them when the battery low.
You will need TASK service password. (3 digits)

caredas

Оффлайн

Вторник, 24.09.2013, 18:36 | Сообщение # 4

Сообщений:

Награды:

Замечания:

Thanks for the answers!

Can you explain more about these errors:

Цитата (Floyd)

1. Machinendaten fehlerhaft
- change two CR123A Lithum cell on the big green circuit board.

If i change the batteries...is it possible to lose machine parameters? And do i need to enter it again or the error will just gone?

Цитата (Floyd)

3. Fehler Leistungsziklen-Daten
- enter the data of 100 cycles (Leistungsziklen-Daten) from documentation through the TASK keyboard. Your laser "forgot"them when the battery low.
You will need TASK service password. (3 digits)

I tried to enter the data, but the situation is the same. May be change of the battery will be enought? Are they the same bateries?
I haven't any documentation about the machine and i don't know this password. Can you help me?

Best regards!

Ilia

Floyd

Оффлайн

Среда, 25.09.2013, 10:17 | Сообщение # 5

Сообщений:

Награды:

Замечания:

Change the batteries on the powered on machine one by one. It will not result data loss.
Then turn keys horizontally enter PWD (3 digs) then press F1 and look to the values if they looks like "F0F0" - you loose the data. If there not is ok, look for problem elsewhere.

==ФоРуМ== » TruTops » TruTops » Trumpf TLF750 Problem - need help!

Страница 1 из 1
1